banner
Multi-hole Zirconia Abrasive Film Strips

Multi-hole Zirconia Abrasive Film Strips

These are 70×400mm film-backed sanding strips for hand and block sanding — the places where paper keeps letting you down: edges, door jambs, tight repair zones, and primer that has to be leveled without cutting through. The grain is zirconia alumina on a polyester film backing, bonded resin over resin, finished with a semi-open coat and an anti-loading layer. The V-shaped perforation moves dust out of the scratch line instead of letting it pack up, so the strip keeps cutting across a full panel instead of only the first third of it.

Product Introduction

Jiangxi Golden Abrasives Co., Ltd. is one of the leading manufacturers and suppliers of Multi-hole Zirconia Abrasive Film Strips in China. With abundant experience, we warmly welcome you to wholesale customized Multi-hole Zirconia Abrasive Film Strips at competitive price from our factory. If you have any enquiry about free sample, please feel free to email us.

 

Three places paper strips quietly cost you money

  • Edge tear. Paper fibers break down the moment you fold a strip over a block edge. Once it tears, the scratch pattern becomes uneven, and you have to sand the repair again. Film bends and returns to shape.polyester sanding wet film multihole strip
  • Loading. Dust packs into an open coat, the cut drops, the operator presses harder, and pigtails show up under the topcoat. Perforation plus an anti-loading layer keep the abrasive face working.
  • Reach. A 150mm disc can't reach a 20mm gap around a handle or a lamp pocket. A 70mm-wide strip can - no special tool required.

 

Heavy-Duty Abrasives: Our zirconia polyester strips use premium zirconia alumina abrasives that deliver sharp, powerful cutting action, making them ideal for heavy-duty sanding tasks such as removing paint, rust, or other stubborn materials from metal surfaces. Their self-sharpening abrasives wear in a way that continually exposes fresh edges, ensuring consistent cutting performance over time.

 

Abrasion-Resistant Film Backing: The green film abrasive strips use a flexible and tear-resistant film backing, built to withstand the stress of high-speed wet and dry sanding operations. Unlike traditional paper-backed sanding belts, the Velcro backing resists tearing and edge wear even under heavy use.

 

Unique V-Shaped Hole Design: The V-shaped holes enhance airflow and efficiently remove dust and debris, keeping the work area clean and preventing clogging. This design maintains the cutting efficiency of the strips.

 

Green Film Abrasive Strips Information

Type

AG312

Specification

70*400mm MultiHole

Grit Range

P40-P2000

Grain

Zirconium Alumina

Backing

Polyester film backing

Bonding

Resin over Resin

Coating

Semi-open coating

Anti-clogging Layer

Invisible coating

Application

Automobile painting and refinishing, wood, and metals.

Package

50pcs/customized box, 1000pcs/carton

(Customized packages are available.)

Grit Selection Guide
Grit Stage in the repair
P40–P80 Stripping paint, rust, and heavy mill scale; shaping
P100–P180 Body filler shaping and rough leveling
P220–P320 Primer leveling and intermediate preparation
P400–P600 Fine primer sanding, blending, and prep before topcoat
P800–P1200 Clear coat defect removal and blend edges
P1500–P2000 Final refinement before polishing
Abrasive zirconia film sanding sheets

Where do these strips earn their keep?

  • Automotive refinishing

Primer leveling on flat panels and around apertures, feather-edging a blend into the adjacent panel, and cleaning up jambs and shuts where a disc will not fit. The film backing also means less risk of a torn edge dragging a groove across fresh primer.

Body filler sanding and leveling

  • Primer sanding before sealer or topcoat

Refining sanding marks between repair stages
Fine sanding and blend preparation on clear coat

  • Woodworking and furniture

Between-coat sanding on lacquer and sealer, leveling filled grain, and working profiles and moulded edges that a round disc cannot follow. The film conforms to the curve without cracking.

  • Metalworking

Weld blending, rust spot removal, and surface prep before coating. Run wet to control heat on thin sheet and to keep dust out of the work area.

 

What goes wrong, and what it normally means?

Symptom Usual cause What to do
Strip creeps sideways mid-panel Hook face loaded with lint, or pad worn flat in the centre Brush the hook face before each fit; retire pads that no longer grip at the ends
Ends lift after wet work Strip stored pressed against a wet pad, or pad left saturated overnight Separate strip and pad to dry; never stack wet blocks face to face
Cut drops sharply after ten minutes Loading, extraction switched off, or a grit step skipped earlier Check vacuum first, then the grit history of the panel
Isolated deep scratches appear Swarf trapped under the strip, or a torn edge from a previous fold Clear the strip face over a bin; inspect the leading edge before reuse
Holes sit off the pad channels Pattern mismatch between strip and pad Match the pad, or move to the 14-hole layout for plain blocks
New strips curl out of the carton Tension released after slitting, plus humidity during transit Lay them flat under a board overnight; curl disappears once fitted

 

Golden Abrasives is a professional manufacturer. To meet different sanding needs, our green film sanding belts are available in a variety of grit sizes. The coarse grit is ideal for strong material removal tasks, such as stripping paint or removing burrs, while the fine grit is ideal for finishing operations that require a smooth, polished surface. Its performance is comparable to Sunmight film L312T. If you have any needs, please feel free to contact us by email: sales@goldenabrasives.com.

FAQ

 

 

01. What are 70×400mm V-hole film sanding strips used for?

Precision sanding where control matters more than removal rate - body filler leveling, primer sanding, edge and jamb work, and surface correction before repainting. They also suit wood profiles and weld blending on metal.

02. Are film abrasive strips better than paper-based strips?

For edges, curves, and wet work, yes. Film does not tear at the fold, does not soften in water, and holds a flatter scratch, so one strip lasts longer, and the finish stays consistent. For light dry sanding on flat wood, paper is cheaper and perfectly adequate.

03. Which grit should I choose for primer sanding?

P220–P320 for intermediate leveling, P400–P600 for finer prep before topcoat. The right choice depends on primer hardness and what goes on next - always check the coating manufacturer's sanding recommendation first.

04. Can these strips replace Sunmight L312T or similar products?

They are engineered as an alternative option with comparable performance in automotive sanding applications, offering stable cutting behavior, film backing durability, and consistent surface finish results.

05. Do you support custom sizes and OEM production?

Yes. Strip dimensions, grit grades, abrasive type, and packaging can be customized according to distributor and industrial requirements.

Hot Tags: Multi-hole Zirconia Abrasive Film Strips, China Multi-hole Zirconia Abrasive Film Strips manufacturers, factory, 3m purple finishing film disc, Zirconium Abrasive Polishing Pet Film Sanding Disc, blue film sanding disc, sunmight l312T

You Might Also Like

(0/10)

clearall